Coupling carriage assembly wide or narrow (CMS 933)


Narrow coupling and wide coupling
Narrow coupling and wide coupling

Both carriage assemblies can work together coupled wide in the tandem mode or coupled narrow.

The coupling width depends on:

The following tables show you the relation between the coupling width, the fabric width and the parking area for the yarn carrier.

Needle area with 96" needle bed width

narrow coupling
narrow coupling

Coupling width 54"

Needle area for coupling width 54"
Needle area for coupling width 54"

Coupling width 52"

Needle area for coupling width 52"
Needle area for coupling width 52"

Coupling width 50"

Needle area for coupling width 50"
Needle area for coupling width 50"

Coupling width 48"

Needle area for coupling width 48"
Needle area for coupling width 48"

Couple Carriage Assembly Wide

  1. The order is finished.
    An empty row is automatically set, the icon is shown in the information area.
    1
    Start the machine with the engaging rod and stop it again when the carriage is located shortly after the left reversing position.
    2
    Switch off 40 V power supply.
    3
    Open the locking of the rear panel segments with the square spanner from the enclosed accessories and remove the segments.
    4
    loosen screws (2) and remove them.
  1. Coupling of carriage assembly
    2. 5
    For wide coupling (tandem machine), push the right carriage to the right until the coupling rod (1) can be assembled.
  2. Coupling widths for CMS 933
    3. 6
    Insert the screws (2) and tighten.
    7
    Remove the carriage part in order to replace the cams.
  3. Replace cams for wide coupling
    4. 8
    Place carriage part on contact surface and assembly with carriage assembly.
    9
    Close the rear panel.
    10
    Switch on 40 V power supply.
    11
    Confirm the input with OK.
    12
    Start the machine with the engaging rod.
  4. The carriage stops and the Coupling width ? error appears.
    5. 13
    Start the machine with the engaging rod.
  5. Carriage assembly runs in the creep speed. The control adjusts to the new coupling width.
    6. 14
    Stop the carriage in the left reversing point again.
    15
    Load the knitting program.

При разделени глави, всички игли извън плетивото трябва са свободни.
Всички нишководачи трябва да бъдат позиционирани.

Couple Carriage Assembly Narrow

  1. The order is finished.
    An empty row is automatically set, the icon is shown in the information area.
    1
    Start the machine with the engaging rod and stop it again when the carriage is located shortly after the left reversing position.
    2
    Remove the carriage part in order to replace the cams.
  1. Replace cams for narrow coupling
    2. 3
    Place carriage part on contact surface and assembly with carriage assembly.
    4
    Open the locking of the rear panel segments with the square spanner from the enclosed accessories and remove the segments.
    5
    loosen screws (2) and remove them.
  2. Coupling of carriage assembly
    3. 6
    For narrow coupling (tandem machine), push the left carriage assembly to the right and hook in the coupling rod (1).
    7
    Insert the screws (2) and tighten.
    8
    Close the rear panel.
    9
    Switch on 40 V power supply.
    10
    Confirm the input with OK.
    11
    Start the machine with the engaging rod.
  3. The carriage stops and the Coupling width ? error appears.
    4. 12
    Start the machine with the engaging rod.
  4. Carriage assembly runs in the creep speed. The control adjusts to the new coupling width.
    5. 13
    Stop the carriage in the left reversing point again.
    14
    Load the knitting program.