Helpful knitting rows

When carrying out cleaning, adjustments and repair work, it is helpful to set a certain knitting situation immediately. The following table lists the knitting specifications mentioned in the operating instructions and the online help.

Knitting Specifications

 

Knitting Specifications

Empty Row

< > S0 W0

If you do not want to generate a new knitting program, one of the two possibilities can be used.
However: The previous racking position is retained.

  • Suspend Production
    မန္န်ူရယ္ ေျဖရွင္းျခင္း 1 ->   ထုတ္လုပ္မႈ ဆိုင္းငံ့ပါ
  • Cancel the production
    မန္န်ူရယ္ ေျဖရွင္းျခင္း 1 ->  ထုတ္လုပ္မႈကို ပယ္ဖ်က္ပါ

Empty row with transfer racking

< > VU S0 W0

Empty row with half racking

< > V# S0 W0

Transfer row to the rear (R = all needles)

< > S:U^SR; S1

Transfer row to the front

< > S:UVSR; S1

Knitting specifications for machines with additional beds

 

Knitting Specifications

Both knitting rows are necessary:

  1. Transfer from front needle bed to rear additional bed
  2. Transfer from rear additional bed to front needle bed

< > S:UNVZ^SR; S3

< > S:UZ^NVSR; S1

Both knitting rows are necessary:

  1. Transfer from rear needle bed to front additional bed
  2. Transfer from front additional bed to rear needle bed

< > S:UN^ZVSR; S3

< > S:UZVN^SR; S1

Generate small knitting program:

    1
    Stop the carriage shortly after the left reversing position.
    2
    Exit the production
    ေအာ္ဒါ သတ္မွတ္ရန္ -> ေအာ္ဒါ တည္းျဖတ္ရန္ -> ထုတ္လုပ္မႈမွ ထြက္ပါ
    3
    Create a new order
    ေအာ္ဒါ သတ္မွတ္ရန္ -> ေအာ္ဒါ တည္းျဖတ္ရန္ -> ေအာ္ဒါ အသစ္ ဖန္တီးပါ
    4
    Create a new knitting program.
    In the ေအာ္ဒါ အသစ္ ဖန္တီးပါ menu tap the သိုးေမြးထိုး အစီအစဥ္အသစ္ ဖန္တီးပါ button.
  1. Confirm the message. A small knitting program with four lines is created.
    2. 5
    Call-up the new knitting program.
    ေအာ္ဒါ သတ္မွတ္ရန္ -> ပံုစံကို ျပင္ဆင္ပါ
    6
    The knitting program contains four lines:
    40 START
    50 S0
    60 S0
    70 END
    7
    Set the cursor in line 50.
    8
    Tap the button . The editor appears.
    9
    Enter the desired knitting specification using the virtual keyboard.
    For example, you may want to enter a transfer row to the rear on line 50.
    The specifications are as follows: 50 <> S:U^SR; S1
    10
    Repeat this specification in line 60.
    60 <> S:U^SR; S1
     The reason for this: A knitting program must contain at least two lines with knitting specifications.
    11
    Confirm the entry with အိုေက.
    12
    Return to the ေအာ္ဒါ တည္းျဖတ္ရန္ window and enter a higher piece quantity, so that the carriage runs several times back and forth.
    ေအာ္ဒါ သတ္မွတ္ရန္ -> ေအာ္ဒါ တည္းျဖတ္ရန္
    13
    Pull up the engaging rod.
  2. The knitting specification is carried out after the next reversal.
    3. 14
    Stop the carriage if it is in the left reversal again.
    15
    Carry out the work on the knitting machine.
    16
    If you want to control the setting, you can let the carriage move several times back and forth.
    17
    For the resumption of the production load the previous order and start the production.